Power Relays [High Power Switch] Menlo Microsystems

Power Relays

The electrification of everything.

Replace your large, slow, unreliable EM relays with the Ideal Switch. Enable a new era of connected and better protected buildings (residential, commercial, hospitals, airports), transportation (eMobility, Rail, Marine), factories (Robots and Systems), and power distribution (solar, wind, grid, battery).

MM9000 Series Specs

This series is optimized for power switching and power density. Scalable in current carrying and voltage standoff.

	Description	Voltage Type	Standoff Voltage	Current Rating	Contact Resistance	Safety Isolation	Control Voltage	Control Current	Switching Mode	Status
MM9200	Power Switch	AC or DC	300V	10A	10 mΩ	-	90V	9 nA	Cold switching	Sampling

Single Pole Single Throw, Normally Open

MM9200

Power Switch

The MM9200 is a high-power SPST micro-mechanical switch. The innovative Ideal Switch technology enables highly reliable micro-mechanical switches capable of carrying high voltage and high current in a small form factor. The MM9200 provides ultra-low on-state resistance and high off-state isolation, with greater than 10 million operations. Because of its long lifetime, extremely low current consumption, and small form factor, the MM9200 is an ideal solution for replacing electromechanical relays, as well as solid-state switches used for control applications where size, weight, power efficiency and thermal management are critical system-level design parameters.

Product Brief

Access additional design information on the
Menlo Support Portal >

Top view

Bottom view

The MM9200 on an evaluation kit board.

Smart Power Relay

	Relay with MM9200	SSR Relay	EM Relay	Key Benefits
Size	3cm x 2.5cm x 0.4cm 3cm³ (no heat sink)	4.5cm x 5.7cm x 2.2cm 56.4 cm³ (no heat sink) 225.9 cm³ (with heat sink)	4.8cm x 3.5cm x 3.9cm 65.5 cm²	• >90% reduction in volume • No heavy heat sink
Weight	<10 g	320 g	85 g	• 90% reduction in weight • No heavy heat sink
Turn on/off time	30 us	75/100 µs	30 ms	• >1000x faster than EMR
Power consumption	<5 mW	<60 mW	1.5 W	• 80% reduction from SSR • 150x reduction from EMR
Lifetime	>10M operations	>1B operations, decades of life	100k operations	• 100x more operations than EMR

Comparison is based on typical for 10A relay.

High-power impact.

Switches do the heavy lifting to power our world, but current technology (transfer switches, contractors, and industrial circuit breakers, for example) are bulky, power-hungry and slow.

Reduced Size & Weight

Go from multiple bulky circuit breakers to small Ideal Switch boards. This means more than 85% reduction in size and weight for a higher density and smaller footprint.

Reduced Switching Speed

Go from 3-20ms to <10µs arc-free switching. 1,000x faster for safer, more efficient power management.

Reduced Power Consumption

Get rid of high power MOSFET switches. Go from 1.5W EMR, <60W SSR to <10W. That is 150x less power than EMRs, and 80% reduction from SSR for money saved.

Increased Power Rating

High-power handling of EMR in combination with the speed and reliability of SS. Works with all standard voltage ratings.

Increased Reliability

Go from <100K EMR cycles to 10B cycles for the lifetime of a solid-state switch.

Enabling Technology

Turn big things off when sensors signal they’re not needed, like street lights, production lines or building HVAC.

“The Ideal Switch is a tiny, efficient, reliable micro-mechanical switch with unmatched RF-performance and, counterintuitively, high-power handling of 1,000s of watts.”

TONY FADELL
FOUNDER OF NEST
PRINCIPAL AT FUTURE SHAPE